Mill certificates and traceability: what to ask your fabricator for
A mill certificate proves what the steel is. Traceability proves the certificate belongs to the piece in your building. They are two different things, and only one of them can be fixed after the fact.
In this article
The short answer
A mill certificate is the steel producer's record of what a particular cast of steel is — its chemistry, its mechanical properties and its heat number — against the material standard it was made to. Traceability is the separate job of proving that the certificate belongs to the piece now sitting in your building. Certificates can be chased up later. Traceability cannot be reconstructed once the offcuts are in the scrap bin.
Two documents get confused constantly on Australian sites, and the confusion only shows up at handover.
A mill certificate says what a batch of steel is. Traceability says which batch your beam came from. They answer different questions, and a project can have every certificate on file and still have no traceability at all.
What a mill certificate actually contains
It is issued by the steel producer for a cast or heat of steel, and it reports:
- The heat or cast number, which is the identifier everything else hangs off
- Chemical composition — carbon, manganese and the rest, which govern weldability
- Mechanical properties — yield strength, tensile strength, elongation, and impact results where the grade requires them
- The material standard it was produced to
In Australia that standard is usually one of AS/NZS 3678 for hot-rolled plate, AS/NZS 3679.1 for hot-rolled bars and sections, AS/NZS 3679.2 for welded three-plate sections, or AS/NZS 1163 for structural hollow sections. The grade on your drawings — 300, 350 and so on — comes from those.
The chemistry matters more than most builders realise. Weldability is a function of composition, and a section that meets the strength requirement but carries different chemistry than expected can need preheat that nobody allowed for.
Why anyone cares
Non-conforming structural steel has been a live issue in the Australian market for years. Product has entered the supply chain carrying documentation that did not match what was in the steel. The industry response has been to stop treating a piece of paper as proof on its own.
That is what ACRS certification is for. The Australasian Certification Authority for Reinforcing and Structural Steels certifies the manufacturer's ongoing conformance rather than certifying an individual delivery, which means the confidence comes from an audited production process rather than from a document that arrived with the truck. A lot of head contractors and most public sector clients now require it, and it is a reasonable thing to ask for on any structural package.
Traceability is a process, not a document
Here is where packages come unstuck.
Steel arrives with the heat number rolled or marked on it. The moment a workshop cuts a twelve metre length into four pieces, three of those pieces have no mark on them. If nobody transfers the identification, the link between that steel and its certificate is gone — permanently, and silently.
Maintaining it means hard stamping or durable marking of cut pieces, cutting plans that record which mark came from which length, and a way of tying a finished member back through its marks to a delivery docket and a certificate. It is not complicated work. It is work that has to happen at the time, because there is no version of it that can be done afterwards.
How much of it is required scales with the construction category under AS/NZS 5131. A CC1 package and a CC3 package can be the same steel and the same welds with very different traceability obligations.
What to ask for, and when
- At tender: whether certificates are required, and whether ACRS certified material is mandatory
- At tender: the construction category, which drives how far traceability has to go
- Before fabrication: confirmation that the fabricator marks cut pieces and keeps cutting records
- During the job: certificates collected as material lands, not chased at the end
- At handover: certificates matched to the member schedule, not handed over as a loose bundle
That last point is the difference between a handover pack and a pile of PDFs. A certificate nobody can tie to a member does not demonstrate anything.
How we handle it
We buy from established suppliers and keep the certificates as material arrives rather than requesting them at the end of a job. Where the package calls for traceability, cut pieces carry their identification through fabrication and the records are built as the job runs. It is a small amount of discipline each week and it means the handover pack is assembled rather than reconstructed.
Common questions
What is the difference between a mill certificate and a certificate of compliance?
A mill certificate is the producer's test record for a specific cast of steel — its chemistry, mechanical properties and heat number against the material standard. A certificate of compliance is a broader statement that supplied product conforms to a nominated standard, and it may cover a delivery rather than a cast. The mill certificate is the one that carries the actual test data, which is why it is the one that matters when a question is asked.
Do we need mill certificates on every steel job?
Not on every job, but it is worth asking rather than assuming. How much material evidence is required scales with the construction category nominated under AS/NZS 5131, and with what the head contractor or the client requires in the subcontract. Deciding at tender is cheap. Deciding at handover is not, because the records either exist or they do not.
What is ACRS certification and should we require it?
ACRS is the Australasian Certification Authority for Reinforcing and Structural Steels. It certifies that a manufacturer's production consistently conforms to the relevant standard, based on ongoing audit, rather than certifying one delivery. Because non-conforming steel entering the supply chain has been a recognised problem in Australia, requiring ACRS certified material is now common on commercial and public sector work and is a reasonable thing to specify.
Can traceability be re-established after fabrication is finished?
No, not honestly. Once a length is cut and the identification is not transferred to the pieces, the link between the steel in the building and the certificate on file is gone. Anything produced afterwards is an assumption dressed as a record. This is the single strongest reason to settle traceability requirements before material is ordered rather than during handover.
Keep reading
More from the workshop
Standards
Construction categories: CC1 to CC4, and which one your steel package needs
AS/NZS 5131 sorts structural steelwork into four construction categories. Naming the wrong one costs you either inspection you never needed, or paperwork that does not exist at handover.
Welding
GP or SP? AS/NZS 1554.1 weld categories in plain English
AS/NZS 1554.1 sets two weld quality categories. Which one applies changes the inspection, the rework risk and the paperwork you get at handover — so it belongs on the drawings.